Freight Rates and Tools

How freight rates work: LTL class and density, spot and contract truckload rates per mile for dry van, reefer and flatbed, surcharges, and your break-even.

2 guidesUpdated

A stack of wooden EUR pallets with one leaning against it
Photo: Alexas_Fotos / Pixabay

A freight rate is the price to move one shipment, and how it is set depends on the freight. Less-than-truckload (LTL) freight is usually priced from its NMFC freight class and weight, under a carrier’s tariff or contract. A full truckload is usually priced per mile or as a flat amount for the load, at a contract rate agreed in advance or a spot rate for that one load. Either way, a rate only means something once you set it against what the move costs.

This guide takes the questions behind any rate in order: how LTL is priced, how truckload freight rates per mile work, what gets added on top of the linehaul, and whether a rate is worth taking. Each section points to the page or calculator that goes deeper. If you ship LTL, the first section is the one you need. If you broker freight, read the first three. If you run a truck, read them all, because the last one decides which loads you should turn down.

LTLTruckload
Usually priced byClass and weight, through the carrier’s tariff or contractPer mile, or flat for the load
What moves the priceThe NMFC item and, on many items, the density of each handling unitThe lane, dates, weight, equipment and the market that week
Where the deal is recordedThe carrier’s tariff or contract, with the freight described on the bill of ladingA rate confirmation
The usual trapA reclass after the carrier measures the freightA rate that looks fine until you count empty miles

LTL rates and freight class

An LTL shipment is too small to fill a trailer, so the carrier loads it with other shippers’ freight and moves it through its terminals. You pay a rate per hundred pounds set by class, weight and lane, less your discount, plus a fuel surcharge and any extra services. How LTL freight works builds an LTL bill line by line from three large carriers’ published tariffs, and covers LTL vs full truckload, minimum charges and freight claims.

Freight class is a number from 50 to 500 that comes from the National Motor Freight Classification (NMFC). The lower the class, the denser and cheaper to carry the freight usually is.

Class is not a price. The FCDC procedures say the NMFC “contains no rates or charges”. Each carrier applies class through its own tariffs and contracts. Higher classes generally cost more per hundredweight, but no single percentage separates one class from the next, so treat any “class 70 costs X” figure as one seller’s example.

Finding a class takes four steps:

  1. Find the NMFC item. The item decides how the class is set: the standard 13-tier density scale, its own density breaks, or one flat class at any density.
  2. Measure and weigh each handling unit. Take the greatest length, width and height as tendered, pallet and overhang included.
  3. Work out density. Multiply length × width × height in inches, divide by 1,728 for cubic feet, then divide the weight by the cubic feet.
  4. Read the class from the item. Record the item number, sub and class for the shipping papers.

NMFTA’s own example is a 48 × 40 × 45 inch pallet at 450 lb. That is 50 cubic feet and 9.00 pounds per cubic foot (pcf), which is class 100 on a standard-scale item. Our freight class calculator does that sum for one handling unit. Its answer is right for articles on the standard scale and an estimate for anything else. The freight class chart and NMFC codes reference gives the 13 tiers in force since 19 July 2025, explains why five of the 18 classes are not on them, and shows how an item can override the chart.

Three things catch people out:

  • The steps are sharp. A 48 × 40 × 36 inch pallet is class 60 at 1,399 lb and class 55 at 1,400 lb, because 35.0 pcf starts the next tier.
  • The paperwork can change the class. Under NMFC Item 110, density is calculated on each handling unit unless the shipping papers show only a total weight. In the calculator’s example, two pallets rate at 92.5 and 65 when listed separately, and the whole shipment may rate at 70 on the total alone. The bill of lading guide and free form goes through what to write in each box.
  • A negotiated rate doesn’t remove the item. A freight-all-kinds (FAK) rate covers mixed freight under one price, but NMFTA says FAKs “are not part of the NMFC” and that the underlying item still matters for claims and audits.

A wrong class costs more than the correction. Carriers weigh and measure freight at their terminals, re-bill when the figures differ, and many add a fee. FedEx Freight’s 2026 quicksheet, effective 5 January 2026, lists $40 per shipment for reweigh and inspection validation, and other carriers set their own amounts. Household goods and noncontiguous trade aside, 49 U.S.C. 13710(a)(3) gives a shipper 180 days from receiving a bill to contest it, so don’t let a reclass invoice sit.

Freight rates per mile: spot and contract truckload rates

On a truckload priced per mile or flat, class usually doesn’t matter. The quote starts from the lane, dates, weight and equipment. Shippers buy either at contract rates agreed in advance or at spot rates for one load, and a rate confirmation fixes the price, the pickup and delivery details and any extra charges.

  • Contract rates are agreed with a shipper for a lane over months, and wait for renegotiation or renewal to change.
  • Spot rates are set load by load, often on a load board, and swing with the market week to week.

New carriers usually start on spot freight from brokers, because shippers rarely hand contract lanes to a carrier with no history. To compare loads, turn every offer into a rate per loaded mile, then into revenue per total mile once the empty miles to and from it are counted.

Dry van, reefer and flatbed rates per mile

No federal agency publishes a truckload rate per mile for dry van or flatbed freight. The per-mile figures quoted online come from load boards and freight-data companies measuring their own users’ loads, so they are market estimates for a past week, and different services give different numbers. Refrigerated produce is the exception: the USDA publishes its own rates.

TrailerPublic rate dataGuide
Dry vanNone from governmentDry van trucking
ReeferUSDA weekly and quarterly produce ratesReefer trucking
FlatbedNone from governmentFlatbed trucking

For refrigerated produce, the USDA’s Agricultural Refrigerated Truck Quarterly for January to March 2026 put the volume-weighted average truck rate at $2.56 a mile on routes of 501 to 1,500 miles. For flatbed, the only public money signal is cost: ATRI’s 15 July 2026 release found its flatbed respondents ran at an average operating loss of 0.5% in 2025. The dry van guide works through a load that pays $3.08 a loaded mile but $2.70 a mile once 90 deadhead miles are counted, and the flatbed guide adds the unpaid hours of securing and tarping a load to the same sum.

A broker lives on the gap between two prices. On a worked load, a shipper pays $2,400, the carrier gets $2,080 and the broker keeps $320 before its own costs. The gap moves because brokers often buy differently from how they sell. C.H. Robinson’s 10-K says it buys most truckload capacity on a spot basis “even when we are working with the customer on a contractual basis”. Hold that $2,400 contract, let the carrier’s price rise 10% to $2,288, and the margin falls from $320 to $112.

Those swings are real. ATRI’s 2026 operational costs report cites DAT and U.S. Bank data showing dry van contract rates up 9% and spot rates up 31% year over year in May 2026. Spot freight can be repriced load by load, while a contract rate waits for renegotiation or renewal.

How freight brokers get paid sets out that worked load, real margins from public filings and the gap between paying carriers and collecting from shippers. To quote freight yourself, start with the path to broker authority. Once loads add up, a TMS for freight brokers is where rates, rate confirmations and margin by customer and lane come together.

What gets added to the rate

The linehaul is rarely the whole bill. Two extra charges come up often, and both should be settled on the rate confirmation before you accept.

  • Fuel surcharge. A charge on top of the linehaul that moves with the weekly diesel price. No law sets the formula: the EIA says surcharges “are negotiated privately”. A common one is (this week’s diesel price − the contract’s base price) ÷ the contract’s miles per gallon. At the EIA’s $6.127 for the week of 9 November 2026, a $3.00 base and 6.5 mpg pay about $0.481 a mile. The fuel surcharge calculator does that sum and the percent-of-linehaul tables LTL carriers use, and shows how much the base, the MPG and the regional index change the result.
  • Lumper fees. Many grocery and retail distribution centers charge for unloading, and the driver often pays at the dock. Under 49 U.S.C. 14103, a shipper or receiver that requires the help must provide it or pay the truck’s owner or operator for its cost. Lumper fees, who pays and the federal rule covers the receipt, getting reimbursed, and detention pay and TONU, which turn up on the same loads.

Is a rate worth taking?

A rate is only good if it beats your own cost per mile. The best public benchmark is ATRI, the American Transportation Research Institute. Its 2026 report puts the average cost of running a truck in 2025 at a record $2.336 per mile, and $2.21 for truckload carriers. Carriers paid contracted owner-operators an average of $2.08 a mile that year, and truckload respondents averaged a 0.4% operating margin. Read those as a benchmark, not a quote, because the data mostly comes from established fleets and small operators pay more on some lines.

Then price in the two things a headline rate hides:

  • Empty miles. ATRI’s non-tank fleets ran 16.5% of their miles empty. Divide your cost per mile by the share of miles that are loaded. At a made-up $2.50 a mile, that is $2.50 ÷ 0.835, or about $2.99 for every loaded mile just to break even.
  • Today’s fuel. ATRI’s 48.2 cents a mile describes 2025. EIA’s weekly on-highway diesel average was $6.127 a gallon for the week of 9 November 2026, against $3.66 for 2025. At ATRI’s 7.43 miles per gallon, that is about 82.5 cents a mile.

The trucking cost per mile calculator does all of this from your own figures: fixed costs, fuel, your pay, empty miles and fees, giving your break-even and target rate per loaded mile and whether an offered load covers them. Fuel tax is part of the same cost. IFTA charges each state’s tax on the fuel burned there, not where it was bought, and the IFTA calculator works out a quarter’s return across up to five states or provinces from miles, gallons and the rates in IFTA’s tax matrix.

Starting a trucking company shows where this habit fits, including comparing each load’s revenue with your real cost per mile in your first 90 days. The startup cost page works it through itemized budgets for one truck. If you lease on to a carrier, the same sums apply to your pay plan: how owner-operators are paid shows why a higher headline percentage can pay less once fuel surcharge is counted.

Two last costs come off the rate. Freight factoring at 2% to 3% of revenue works out at 4 to 6 cents a mile on ATRI’s averages, which is a lot against a 0.4% margin. And if someone finds your loads for you, a truck dispatcher’s job includes getting a rate that covers fuel, miles and the empty run to pickup, so check the rate confirmation matches the deal.

This page is general information, not legal, tax or financial advice. The class you are billed at is set by the applicable NMFC item and your carrier’s tariff or contract. Every figure here comes from the linked guides, whose facts were checked against primary sources between 31 October and 14 November 2026.

2 guides

All Freight Rates and Tools guides